2001-1501 • MS9470/MS9770 MS9470/MS9770SECURITY AND HOME AUTOMATION SYSTEM
CONTROLS:1. CONTROL INDICATORSComes on when the remote control sends a radiosignal when keys are pressed. When the indicatorblinks only weakly, the ba
key. (e.g. living room lamp, TV, garden lights,etc.).8. BATTERY COMPARTMENT (BACK COVER)INSTALLATION:1. PLACING THE BATTERIESOpen the battery compartm
At the front of the modules, you’ll find 2 codeswitches: Unit Code (1 through 16) and HouseCode (A through O). Take care that when you areusing the mo
13MS9470/MS9770 5.PROGRAMMINGTHE SC2700 BASE STATION5.1 REGISTRATION OF RADIO SENSORSEvery sensor must be installed or registered with the base stati
Up to 8 remote controls can be registered with the base station (KR10/1 and SH624/1).1. Set mode switch to the INSTALL position: All indicators of occ
15MS9470/MS9770 5.4 PROGRAMMING TELEPHONE NUMBERThe Marmitek sc2700 base station has a standard telephone dialler. In case of a alarm, up to 4 teleph
16 MARMITEKThe alarm message of the telephone dialler can be recorded and re-recorded when required. The message can be up toapprox. 12 seconds. It is
17MS9470/MS9770 5.6 DELAY TIMESARMINGWhen arming the security system by means of the remote controls KR10/1 or SH624/1 in the ARM AWAY mode, the syst
18 MARMITEK5.7 JAMMING DETECTOR ON/OFFThe Marmitek sc2700 base station is equipped with a system to detect strong external interfering signal that may
19MS9470/MS9770 5.8 CHANGING YOUR PERSONALIDENTIFICATION CODEThis access code, is your Personal identification code. When you have changed this code,
2 MARMITEKINTRODUCTIONCongratulations! You purchased a Marmitek MS9770/9470 Security System.Marmitek Security Systems are quality products and are man
20 MARMITEK5.9 ERASING OF A REGISTERED SENSOR5.10 ERASING OF ALL SETTINGSIn case it is required, you can reset the base station to the factory default
INSTALL – Position for installing sensors and for changing system settings. RUN 1 – For normal alarm operation.RUN 2 – For normal alarm operation. Wh
6.3 WHEN AN ALARM SITUATION OCCURS• An alarm situation can only be detected when the sc2700 base station is armed• An instantaneous or delayed alarm i
The security system can be disarmed by means of the KR10/1 and SH624/1 remote control or by using your PIN on thekeyboard of the sc2700 base station.1
A panic alarm can be activated at any time in case of an emergency, regardless if the system is armed or disarmed.You can activate a panic alarm in th
25MS9470/MS9770 Your security system is equipped with a wide variety of functions to control lights, extra sirens, appliances and sunshades,throughou
FUNCTION ADDRESSESFunction: Address: With ref. address A1: With ref. address B3:Alarm light [HC+[UC] A1 B3All lights [UC] A BStatus Indicator [HC] + [
For using this function, you need the Glass BreakSensor GB10 (optional). This sensor contains aphotocell that (at dusk) starts a programsimulating you
Your SC2700 base station is equipped with a dial-in function. You now can control your security system from every touchtone phone or mobile. You also
When an error occurs in one of the motion or door/window sensors (e.g. battery low), you can program the base station toreport this via phone. This is
3MS9470/MS9770 1 GENERAL• Marmitek systems are designed for use in dry environments.• Avoid placement of system components in environments with extre
30 MARMITEKThe security system does not operate:Check that the POWER indicator on the sc2700base station is on. If not, check that the PS500power supp
N.B.: When replacing the batteries of thesensor when the system is operational, you canmake sure that the sensor maintains its uniquecode avoiding re-
4 MARMITEK3 MARMITEK SYSTEMS3.1 COMPONENTSMARMITEK SYSTEMS CONSIST OF THE FOLLOWING PARTS:1 SC2700 SECURITY CONSOLE(BASE STATION)2 PS500 MAINS ADAPTOR
5MS9470/MS9770 4 INSTALLATION OF THE COMPONENTS4.1 SIGNALS AND RANGEYour security system is using variouscommunication techniques. For a goodundersta
4.2THE SC2700BASE STATION1. PANICWhen pressed, this red button initiates animmediate alarm.2. ARM HOMEAlarm function when being at home. Only doorand
7MS9470/MS9770 14. TIME OFFUsed to set the Lifestyle mode. When pressing thiskey at a certain time, the Lifestyle program will beswitched off every d
CONTROLS:1. CONTROLINDICATORWhen you pressthe button TEST, orwhen the unit istransmitting asignal to the basestation, thisindicator will come on. When
3. CODEBy pressing this key, the sensor gets a new code (1out of 65.536).N.B.: When the sensor has been installed on thesystem already, you have, afte
Commentaires sur ces manuels